PRODUCTS
PRODUCTS
Check category
-
-
Precautions for using machining center

Precautions for using machining center

  • Categories:News
  • Time of issue:2022-02-18 17:26
  • Views:

(Summary description)Adhering to the safety operation rules when using the machining center is not only a condition to ensure the personal safety of the operator, but also a condition to ensure the normal operation of the machining center. At the same time, the conditions for safe operation are the requirements for scientific use. Recognize whether the external environment of the CNC machining center is normal.

Precautions for using machining center

(Summary description)Adhering to the safety operation rules when using the machining center is not only a condition to ensure the personal safety of the operator, but also a condition to ensure the normal operation of the machining center. At the same time, the conditions for safe operation are the requirements for scientific use. Recognize whether the external environment of the CNC machining center is normal.

  • Categories:News
  • Time of issue:2022-02-18 17:26
  • Views:
Information

Adhering to the safety operation rules when using the machining center is not only a condition to ensure the personal safety of the operator, but also a condition to ensure the normal operation of the machining center. At the same time, the conditions for safe operation are the requirements for scientific use. Recognize whether the external environment of the CNC machining center is normal.

Whether the emergency stop is in a depressed state; whether the power cord is connected normally without damage; whether the lubricating oil is sufficient for the machining center After the operation is completed, close the power supply of the peripheral equipment of the CNC machining center, clean the machining center and the surrounding sanitation, clean up the processing waste, clean the bed, Spindle, tool magazine, tool holder.

  Before the official start-up, the peripheral equipment of the CNC machining center (such as an air compressor) should be turned on and then powered on from the main power supply to the machine tool. First release the emergency stop, and then operate the handwheel to slowly move the CNC machining center to recognize that the machine tool can move normally in all directions; normal rotation of the spindle ensures that the spindle can rotate.

   Perform the tool change action to ensure the normal tool change of the tool magazine; perform the four-axis tightening and loosening to ensure that the four-axis can be clamped and loosened normally; perform the machining fluid circulation action to ensure the normal circulation of the machining fluid. The following points need to be paid attention to when installing the knives. First, clean the selected knives to ensure that there are no oily impurities on the knives.

Keyword:

HOT NEWS

02-18
2022
Three control methods of wire cutting machine

There are three control methods for CNC wire cutting machine tools, namely: profiling control, photoelectric tracking control and digital program control

02-18
2022
Precautions for using machining center

Adhering to the safety operation rules when using the machining center is not only a condition to ensure the personal safety of the operator, but also a condition to ensure the normal operation of the machining center. At the same time, the conditions for safe operation are the requirements for scientific use. Recognize whether the external environment of the CNC machining center is normal.

02-18
2022
A detailed introduction to wire cutting

The mechanical part of the wire cutting machine tool is the foundation, and its accuracy directly affects the working accuracy of the machine tool, and also affects the full play of electrical performance. The mechanical system consists of machine bed, coordinate table, wire transport mechanism, wire frame mechanism, taper mechanism, smoothing system, etc. The machine bed is usually of box-type construction.

02-18
2022
Precautions for operating a surface grinder

When it comes to surface grinder machine tools, people think it is the kind of machine tool that grinds flat. The development trend of surface grinders in the world has changed in the past. Nowadays, the development trend of surface grinders is to turn to forming, step, plunge, fast vibration, and three-dimensional space curve surface grinding. It can be said that flat grinding is a type of grinding machine with great potential for evolution.

×

搜索

Search

Tiangong Machine Tool Manufacturing (Changxing) Co., Ltd.

TEL:0571-86330505 013905819163 

013805797361

E-mail:hz_tg@126.com

 

Add:No.1 Lvmeng Road, Lushan Township, Changxing County Development Zone, Huzhou City, Zhejiang Province

© Tiangong Machine Tool Manufacturing (Changxing) Co., Ltd.      浙ICP备2022002080号-1  SEO

×